Shandong Xin Ze Equipment Co., Ltd. specializes in energy-saving new wall materials, building fire insulation, building decoration materials technology cement foam insulation board equipment, the external walls of fire insulation board equipment and other building materials machinery design. Tel 182 6305 1438 QQ 3213319791 external walls of fire insulation board equipment Features; 1, high fire resistance. Is an inorganic material, it is a Class A fire protection materials, which has a good fire resistance, refractoriness reach above 1000 ℃, fully meet the requirements for fire resistance of external wall insulation board. 2, high thermal insulation closed cell ratio> 95%, high closed cell ratio of the heat transfer due to low air flow, is a prerequisite for high insulation. So the production of external wall insulation board thermal conductivity of 0.045-0.068w / mk, and polystyrene board thermal conductivity slightly lower, but in practical engineering effect is roughly equal, to meet building insulation needs. 3, relative strength, and not broken. The company produces compressive and flexural strength without board were higher, reaching a relatively uniform low-density high strength, use and transport are difficult to break, and comply with fire integrity. 4, light quality light adhesive strength is another advantage of our products. Density 150-300kg / m3, to achieve the requirements of the external wall insulation board and reduce costs. Compatibility of materials is good, strong bond with the wall. 5, non-toxic and environmentally friendly energy based mineral aggregates cement production as the main raw material, the high temperature will not burn and no toxic gas release, are safety and environmental protection materials, and the support of national industrial policy. 6, long life of the current building design life is generally 50 - 100 years. The organic insulation materials design life, but most only 20--25 years. That is the life of the insulation layer and the building can not keep pace. This means that the aging of organic insulation materials impatience makes a building in the course of their service to be carried out at least 2-4 times the insulation construction. This repeated operation of the building's construction, causing direct damage to the building itself. Reducing the use of the building, while many people also each insulation construction production and living seriously inconvenience. Inorganic insulation life of more than 50 years, the life of the building may be the same. Cement foam insulation board equipment, the external walls of fire insulation board equipment main purposes: external wall insulation materials used in construction, fire buffer zone, roof insulation materials. External walls of fire insulation board equipment ||, according to customer requirements customized production, energy-saving Equipment Co., Ltd. Shandong Xin Ze quality assurance, peer lowest, welcome to visit to buy! 1. The use of a machine to produce 5 cm, light 10 cm, 15 cm thickness of the insulation and other composite flat, lightweight insulation composite corrugated board, building partition walls, various sizes of large format color tiles, building templates, new fire board, inorganic glass insulation coop board. 2. The machine uses dual drive roll extrusion process, from product sizing, ingredient, spreading, compound, complex pressure-time completion of the entire board production line process, the production does not require 2 to 3 million plastic pallet rack investment, high degree of automation equipment. Greatly reducing the labor intensity of production workers. 3-5 people can produce 700 square meters per day, thickness than the traditional manual mode provincial labor 40% 3. FRP can be adjusted (from 2mm-50mm) was poor flatness 0.001mm. 4. Product surface flat, smooth, dense and high, truly realize the industrialization of new production lines building wall panels. 5. The production line can produce corrugated board, perfect waves lapping process, eliminating the need to make the roof waterproof flat fee, saving 8-15 yuan per square meter. 6. Since the device uses self-propelled rail design and production of products in each trip orbit reusable logic stack 4-6 layers, and can set up multiple times orbit, saving production sites. 7. The cost savings template, template traditional equipment is very thick, and our equipment template thin. 8. The slurry can be added to the crop straw, sawdust, straw (shell), fly ash, and waste recycling, energy saving and reduce costs. Main technical parameters of the device dimensions: 42 m long × 7.5 m wide × 5 meters high, batching equipment: length 13 m × 4.5 m wide × 4.5 m high insulation board production process equipment foam cement insulation board equipment production process 1, the material, mixing: feeding system through quantitative cement, foaming agents, foam stabilizing enhancer added to the mixer, dry mixing for 30 seconds; 2, mixing: the quantity of warm water added to the mixer, wet stirring for 2 minutes; the quantity of hair foaming agent added to the mixer stirring 8-15 seconds; 3, injection molding, foaming: then the slurry is injected into the mold foam, foaming process approximately 3-5 minutes; 4, the initial conservation: Some standing after the completion of the injection molding hours early conservation; 5, the release: be foamed cement board to complete the initial setting, you can have the initial strength when stripping; 6, cutting: cutting can be carried out with a certain strength of the insulation board blank after stripping, cutting specifications according to Adjust the cutting blade; 7, finished conservation: foam cement board curing period should not be less than seven days. Inorganic fiberglass insulation board equipment production process 1, dual drive roll extrusion process, from product sizing, ingredient, spreading, compound, complex pressure-time completion of the entire board production line process, a high degree of automation equipment, smooth operation, specifications any adjustments. Product surface flat, smooth, dense and high, truly industrialized assembly line production of new building wall panels. Greatly reducing the labor intensity of production workers. 2. inorganic fiberglass insulation board production equipment capable of producing corrugated board, perfect waves lapping process, eliminating the need to make the roof waterproof flat fee, saving 3-6 yuan per square meter. 3. FRP thickness can be adjusted difference 0.001mm 4. feed (from 0.2mm-50mm) high average thickness of flat objects, mix syrup, spreading, complex, pressing a molding, 3-5 to produce 700 square meters per day, provincial labor than conventional equipment 40% 5. save space, can produce the 4-7 layers per trip tracks, greatly reducing the footprint (700m2 daily production to 200 m2 plate plant will be able to save the investment 6. conventional equipment use templates make it thick, and our equipment template thin than conventional equipment can save investment perlite insulation board equipment production process automatic feeding machine feeding - automatic mixing - one can automatically suppress the two plates - Automatic ejection - automatic transmission, automatic spray-time automatic completed within 15 seconds --20 seconds, each producing two plates Mobile: 18263051438 Contact QQ: 3213319791 Contact: Xie Jingli.